Tankless Water Heaters in Clinton Township, MI
Considering tankless?
We install, repair, and maintain tankless water heaters and can help determine whether your home is a good fit before you choose a system.
Tankless Water Heater Installation, Repair & Maintenance
A tankless water heater heats water as it is needed instead of storing a large volume of heated water.
When properly sized and installed, tankless technology can provide continuous hot water within the unit's capacity, reduce standby heat loss, and take up less floor space than a conventional storage tank.
But tankless is not automatically the right choice for every home.
The installation can involve gas capacity, venting, electrical requirements, plumbing changes, condensate drainage on applicable models, and equipment sizing.
The best decision starts with understanding your home's actual hot-water demand.
How a Tankless Water Heater Works
When a hot-water fixture opens, the system detects water flow.
Depending on the model, the heater then uses:
- A gas burner and heat exchanger
- Electric heating elements
- Flow sensors
- Temperature sensors
- Electronic controls
The water is heated as it passes through the unit.
When the fixture closes, the system reduces or stops heating.
Unlike a conventional storage tank, the system does not need to continuously keep a large volume of water hot.
Tankless vs. Traditional Tank
| Feature | Tankless | Traditional tank |
|---|---|---|
| Hot-water supply | Continuous within capacity | Limited by stored capacity |
| Storage tank | No | Yes |
| Standby heat loss | Minimal/no tank standby loss | Yes |
| Space | Usually compact and wall-mounted | Requires floor space |
| Upfront installation | Often higher | Usually simpler |
| Gas/electrical changes | May be needed | Often simpler when replacing like-for-like |
| Maintenance | Model-specific | Periodic maintenance |
| Sizing | Flow rate + temperature rise | Tank capacity + recovery |
The right system depends on the household and the home.
Is Tankless Right for Your Home?
Tankless may be a good fit if:
- You regularly run out of hot water.
- You want a compact wall-mounted system.
- You value continuous hot water.
- Your home can support the required gas or electrical capacity.
- You plan to keep the system long enough for the investment to make sense.
Think carefully if:
- The existing gas system has limited capacity.
- Venting would be difficult.
- The electrical panel has limited capacity for an electric unit.
- Several high-flow fixtures regularly operate simultaneously.
- Minimizing upfront installation cost is the priority.
Sizing: Flow Rate and Temperature Rise
Tankless sizing is one of the most important parts of the installation.
Two major factors are involved.
Flow rate
How much hot water might the home need at the same time?
For example:
- Shower
- Second shower
- Kitchen faucet
- Dishwasher
- Washing machine
The system needs enough capacity for the expected simultaneous demand.
Temperature rise
The unit must raise incoming cold water to the desired hot-water temperature.
The colder the incoming water, the more heating capacity is required.
This matters in Michigan because winter incoming water can be much colder than summer water.
A unit should therefore be sized using realistic winter conditions rather than relying on warm-weather performance.
Gas Tankless Installation
Gas tankless units can have substantial gas-input requirements.
The existing system should be evaluated for:
- Gas capacity
- Gas piping
- Shutoff arrangement
- Venting
- Combustion-air requirements
- Electrical supply
- Condensate drainage where applicable
- Plumbing connections
- Required clearances
An existing gas line that worked for a conventional tank does not automatically mean it is adequate for a higher-input tankless unit.
Venting
Tankless gas water heaters do not necessarily use the same venting arrangement as conventional storage heaters.
Requirements depend on the specific model.
Condensing and non-condensing systems can have different venting and condensate requirements.
The installation must follow the manufacturer's instructions and applicable code.
Electric Tankless Installation
Electric tankless systems have a different set of considerations.
Whole-house electric tankless heaters can require substantial electrical capacity.
Before selecting a model, the home's:
- Electrical service
- Main panel
- Available capacity
- Circuit requirements
- Wiring
should be evaluated.
Choosing a heater first and discovering afterward that the electrical system cannot support it is the wrong order of operations.
Tankless Water Heater Repair
Tankless units can develop problems involving:
- Error codes
- Ignition
- Flame sensing
- Flow sensors
- Temperature sensors
- Scale buildup
- Heat exchangers
- Venting
- Combustion
- Condensate drainage
- Electrical components
- Water leaks
An error code can help identify the area of concern, but the code itself does not always mean a particular component should simply be replaced.
Diagnosis matters.
Maintenance and Descaling
Mineral scale can accumulate inside a tankless heat exchanger.
Depending on the model and water conditions, periodic flushing or descaling may be required.
The correct maintenance schedule depends on:
- Manufacturer
- Model
- Water conditions
- Household usage
- Installation conditions
Some manufacturers recommend annual descaling.
The manufacturer's instructions should be followed rather than applying one universal six-month or twelve-month schedule to every tankless system.
Clinton Township Water Conditions
Clinton Township receives municipal water from regional sources including the Great Lakes Water Authority and the City of Mount Clemens.
Current water-quality information places total hardness around 105โ112 mg/L, or approximately 6โ7 grains per gallon.
This is generally considered moderately hard water.
Moderately hard water can contribute to mineral deposits over time, which is relevant to tankless heat exchangers.
It does not automatically mean a softener is required.
Instead, the equipment's maintenance requirements should be followed and the actual condition of the system should be considered.
Tank-to-Tankless Conversion
Replacing a conventional tank with tankless can involve more than changing the equipment.
The installation may require evaluation of:
- Gas capacity
- Gas piping
- Venting
- Electrical supply
- Water connections
- Condensate drainage
- Mounting location
- Clearances
- Service access
- Drainage
A proper site evaluation should happen before selecting the unit.
Power Outages
Gas tankless systems use electricity for controls and ignition.
That means a gas tankless unit generally will not operate normally during a power outage without appropriate backup power.
This is worth considering for homeowners who want hot water available during storm-related outages.
Tankless Installation Process
Understand your household's hot-water use
We look at the number of occupants, fixtures, and likely simultaneous demand.
Evaluate the installation location
We check gas or electrical capacity, plumbing, venting, drainage, and access.
Size the unit
The unit is selected based on expected flow and temperature rise.
Explain the installation requirements
If gas, electrical, venting, plumbing, or condensate changes are needed, those are explained before work begins.
Provide upfront pricing
You receive the scope and applicable pricing before approved work starts.
Install and test
The system is installed according to the manufacturer's requirements and applicable code, then tested.
Tankless Considerations in Clinton Township
Moderately Hard Water
The local water hardness makes scale something worth considering during tankless ownership.
Cold Incoming Water
Winter conditions increase the temperature rise the unit must provide.
Existing Infrastructure
Older homes may require closer evaluation of existing gas, electrical, plumbing, and venting infrastructure.
Basement Installations
Basement or utility-room installations require planning for venting, drainage, condensate, and service access where applicable.
Frequently Asked Questions
They can be for the right household. They offer on-demand hot water, a compact footprint, and reduced standby heat loss. The higher installation cost and possible infrastructure upgrades should be considered.
It can provide continuous hot water within the unit's capacity. If demand exceeds the unit's capacity, available hot-water flow can be limited.
Possibly. Gas tankless units can have substantially higher input requirements than conventional tanks. The existing gas system should be evaluated.
Gas tankless systems generally require electricity for controls and ignition, so they typically will not operate normally without backup power.
Follow the manufacturer's maintenance schedule. Some manufacturers recommend annual descaling.
Error codes can indicate ignition, flow, temperature, venting, overheating, or other conditions. The specific code should be diagnosed according to the manufacturer's documentation.
It is a brief burst of cooler water that can occur when hot water is turned off and then used again shortly afterward. The effect depends on the system and plumbing configuration.
Yes, provided the installation meets the manufacturer's requirements and applicable plumbing, mechanical, fuel-gas, electrical, venting, drainage, and clearance requirements.
The applicable requirements depend on the project. Tankless installations can involve plumbing, mechanical, gas, and electrical work, each of which can have separate requirements.
Related Plumbing Services
Thinking About Tankless?
Before buying a tankless water heater, make sure the unit matches your household demand and that your home can support the installation.
Call (586) 500-5250 for tankless water heater installation and repair in Clinton Township.